Metal casting furnace
My aim this year is to cast my own bronze sword, and to do that I need to melt the bronze. I just made a bucket furnace that's good enough to melt copper and tin, the metals in bronze alloy. My furnace is based on the Mini Metal Foundry on Youtube.
Here are ingredients to make it.
- 10 litre metal bucket - the body of the furnace
- 5 litre plastic bucket - to make a void in the centre of the furnace
- 15 litre plastic bucket - to make a lid for the furnace
- Tin can - to make a void in the centre of the lid, to release pressure
- Two metal hoops - these will become handles for the lid
- 1 inch steel pipe - this is the air intake for the furnace
- 25kg dense castable from Castree Kilns
- dog - serves no useful purpose
Making the lid
First of all I made the lid, with 10kg of the dense castable and 1.3 litres of water, mixed thoroughly.
I set the tin can in the centre of the mix and sunk the handles into it. Then I let it cure for 48 hours. The dense castable material is strange stuff, it's very dry and at first I didn't think it was going to cure. But 48 hours later it's hard as rock.
Making the body
I needed to make a hollow body for the furnace, so I used a small bucket filled with water in the centre to make the void.
I used 15kg of dense castable with 1.95 litres of water, which pretty much filled the bucket. I let this cure for 48 hours as well, and spent several hours cleaning all the gack off the kitchen table, floor and ceiling.
The mistake I made here was spilling some of the dense castable into the white bucket in the middle. When I poured the water out, there was a 2cm layer of rock hard material in the bottom - turns out it sets underwater just fine! I hacked it into little pieces and pulled it out with no problems.
Once it had set, I used a hole saw to cut a piece out of the side, and fitted a steel pipe to force air into the furnace. This is hooked up to Kat's hair dryer - shh, don't tell her!
Here's the finished furnace, the next step is to fire it up!
Here are some pics of the first time I lit it up, to melt some aluminium as a test. Aluminium melts at a much lower temperature than bronze, so it's easier to work with and cheaper.
The crucible is made of ceramic bonded clay graphite, it's a Salamander A2 from Castree Kilns. It's rated to 1600°C. The original instructions I followed used an old fire extinguisher, but I've been told that these are quite unreliable and prone to sudden failure.
Finally here's a quick video of the furnace in action:
The next step is to make a sword template out of wood and then cast it.
I've no idea how that works but it's going to be fun finding out!
In ten days we're leaving the UK for new adventures in Spain...Read more
Archive2016December 2016 (2)November 2016 (2)October 2016 (2)September 2016 (3)August 2016 (4)July 2016 (5)June 2016 (4)May 2016 (4)April 2016 (5)March 2016 (4)February 2016 (4)January 2016 (5)2015December 2015 (4)November 2015 (4)October 2015 (5)September 2015 (4)August 2015 (4)July 2015 (4)June 2015 (4)May 2015 (5)April 2015 (4)March 2015 (4)February 2015 (4)January 2015 (4)
What's this about?
Hi I'm Mat and I'm addicted to new hobbies. I used to think this was a bad thing but now I'm embracing it.
Writing them all up in this blog encourages me to finish projects, and helps me keep track of which ones I've tried.
I recently caught up with a good friend, Vicky, who rivals me in terms of how many different hobbies she has...
Also in Making things...
I've wanted to try this ever since I saw Fight Club! I've seen several methods for making soap, but I'm always attracted to using dangerous chemicals, so lye seemed the obvious way to go...